Ok, This took me most of my afternoons all last week and two weekends, including this past saturday and sunday. I took some pics, but I'm not posting them in this blog entry. I just wanted to get the work done and messing with a camera took too long so I didn't get many pics at all.

Parking brake/emergency brake/e-brake update!

After grinding the brake shoes down a bit so they'll fit inside the rotors smoother, I realized the adjustment pins were rusted to all hell and wouldn't function correctly anymore. Whenever I pushed on the e-brake inside the car, the shoes would only move a centimeter. $20 at advanced auto for the parking brake hardware kit and I got everything swapped out except for the metal pivot piece. The replacement piece for that was rediculously small and would no way in hell work in my opinion. So I got the old ones cleaned up, greased everything with a lithium grease instead of caliper grease so there would be lease junk in there to mess it up, and after a long while I got it all working good again by holding everything in place while smacking the shoe into place. And after that, I put in the new retaining clip and those shoes were held in place tight and when applied, they moved a half inch. Yay. All done with that.

After fixing the e-brake, the car still pulsated when braking. Everyone says its rotors. Seeing as the back rotors looked like shit since the back plates tore one up and the caliper pins caused the pads and rotors to wear uneven, I replaced the rotors and pads. I bought the parts from Napa this time. I had to file down my brake pad holding brackets to get some rust off. I also had to lightly file down the ends (not the nubs) of the brake pads so they'd have movement once they were in the bracket. And get this, the NAPA brand rotors and pads were a higher quality than what I got at advanced auto parts or autozone and where a little over $100 cheaper! I'll only buy parts from NAPA from now on. BTW, the NAPA back rotors were different on the inside than the wagner ones I originally got from autozone. Inside the NAPA rotors, it was a smooth tapered gradient inside the hat, compared to the hard edged line of the crap rotors that kept smacking my e-brakes. I may not have had to grinded my e-brakes at all if I would have had these rotors from the beginning! Fuck you autozone! Also, after doing the backs, I bled the entire brake system.

After the back rotors and pads were done, the e-brakes fully done, brakes bled... The car still pulsated while braking, but! All the noise in the back end is now completely gone and the braking was a slightly different pulsating now.

Now that all the rotors and pads are all brand new, I noticed scuff marks on my new front rotors from the pulsating bullshit. So I figured it must be the calipers. The front wheels were a bitch to move compared to the rears with the brakes off. So I picked up the front calipers with bracket for $54 a piece at NAPA, $90 a piece if I remember right at advanced auto and autozone. Fuck both of them.

I replaced the front calipers, just like I replaced the ones in my Saturn blog. Turns out the front calipers were not fully releasing. After getting the new calipers on, the tires moved much much easier when the brake was off.

Guess what tho! The brakes still pulsated.. But once again, it was a slightly different pulsation again and this time with all the noise from all the bad braking parts gone, I was able to hear a distinctive electric motor noise kicking in with the pulsation. Turns out I have an ABS problem on top of everything. I pulled the two ABS fuses, (the ABS light comes on on the dash now). With the ABS disabled, the damn thing brakes perfectly fine now. YATTA!

I've let the blazer sit the past couple days so I can check the brake fluid level to make sure theres absolutely no leaking going on at all. Other than that, I'll give it another test run this weekend to some local stores to see if all my vibration problems were fixed too. If not, then theres something else going on with that, but I'll get to that some other time if its a persistent problem.

As far as I can tell, the ABS problem is probably one, if not both of the front ABS sensors. Each costing about $70 piece. As far as I'm concerned it can wait until we're closer to winter because I don't want to fuck with this truck anymore.