Search the Community

Back in May of this year I bought a new Smoker because I've been thinking about trying out smoking food for a couple years now. I've gotten pretty good with a standard grill, but I wanted to improve my slow cooking skills and try something new with different flavors. After watching numerous seasons of BBQ Pitmasters, I became inspired to finally try out charcoal smoking. Instead of buying something expensive, I shopped around, looked at reviews, different makes and models and I decided to go with a vertical charcoal water smoker. A vertical water smoker works by having a heat source at the bottom, a water pan in the middle of the smoker that provides hot moisture, and two cooking grates. One directly over the water pan and the second at the top of the smoker. Because the water pan is almost as wide as the smoker itself, it causes all the food in the smoker to be cooked with indirect moist heat. Vertical water smokers are also cheap. Some offsets are cheap also, but many of the low end vertical water smokers are under $60. After reading many reviews, I decided to get a Brinkmann Gourmet Charcoal Smoker. There is a large community of people that use this exact smoker and have shared numerous modifications they have done to improve it's performance. After reading about smoker modifications I was a bit concerned. Why would a new product need modifying? Well, I found out the answer.. If I wanted a smoker that would work amazing right out of the box, I'd have to pay $300 for a Weber Smokey Mountain. So, no.. I decided to go with something cheaper and modify it if needed, hence why these Brinkmann ones are nick named the ECB (El Cheapo Brinkmann). I'll only be using this smoker about 5 months out of the year and not even every week. For what I wanted to do, I figured $90 on amazon was good enough. For that price I also got the smoker cover, which turned out to be better material than I thought it would. Unfortunately, amazon shipped this smoker horribly. The box looked like it was kicked a few times and I had to hug the metal of the body and the lid back into a fully circular shape. As well as bending the door into a shape that would close correctly.. I also needed to use a rubber mallet and hammer out one ding in the body. I was not please with the condition, but after full assembly the smoker looked great. Here are some pictures of the Smoker new and in use for the first time: I never used charcoal before so I had to buy a new charcoal chimney starter and some charcoal. I decided to get the weber chimney and go right for the royal oak lump charcoal. After reading all the safety information about charcoal lighter fluid and how you need to let the charcoal burn out for at least 20 minutes, etc. I had no interest in using it.. thats why I got the chimney starter. Along with some newspaper I'm able to get any charcoal started burning safely. That and I have a friend that uses the same style of chimney to start his charcoal grill. Very simple to use. The bottom of the smoker is a charcoal pan with air vents on the bottom. Charcoal is controlled completely by air flow. I added a grate at the bottom because I read that burned charcoal ash will build up and block the air flow which would smother the remaining coals. Now that the coals are ready, I put the body of the smoker on top of the pan, then add water to the water pan, put on the grates and add the food. Put the lid on and its done. As you can see, this style of smoker is noticeably smaller than an offset charcoal smoker that can usually be about the size of a normal grill. For my first use, I went big. I put a pork shoulder on the bottom grate and a rack of ribs on the top. I figured I'd get a good feel for the smoker with two different things cooking at once. I also put a couple aluminum foil packets of soaked hickory and apple wood chips onto the charcoal.. Here is where the smoke starts rolling pretty good: About 4+ hours later here are the results: The end results were not what I was expecting. Because this smoker has no airflow controls, I could not regulate the temperature. Also the thermometer is horrible. It doesn't even have temperatures.. only "warm, ideal and hot". The ribs turned out ok, but overly smoked. The smoke flavor was so pronounced that I couldn't eat the smaller ribs. And the pork shoulder was not even cooked all the way through. I ended up finishing the pork shoulder on my propane grill because I already used 2 chimneys full of charcoal and I didn't feel like setting another to burn. The pork shoulder was not cooked correctly but the smoke flavor was good for it. Because it was thicker, the smoke didn't permeate as much into the meat. I'd say this smoker was a failure. But I didn't give up. I decided to make a few modifications, which I'll go over in another blog post. I can say that I would not recommend using this smoker without modifying it. Or if you do use this smoker without modifications do not use lump charcoal. It burns far hotter and faster than kingsford briquettes and with no airflow controls, the lump burned incredibly fast. Also, use almost boiling water in your water pan, and only fill it half way. The water I used was hot from the tap and because of the volume of water the pan holds, most of the heat that would have cooked the pork shoulder was absorbed by the water that was sitting directly under it. And for anyone wondering, was the smoker worth it? The answer is yes. Once I had the proper modifications done, I have been making some of the best barbeque I've ever eaten. Definitely worth it. It was quite a learning experience too. Practice makes perfect.